Robert H. Wagoner

• J.F. Wang, R.H. Wagoner, D.K. Matlock and F. Barlat: Anticlastic Curvature in Draw-Bend Springback, Int. J Solids and Structures, Vol. 42/5-6, pp. 1287-1307, 2005.
  
  
• J. Wang and R.H. Wagoner: A Practical Large Strain Solid Finite Element for Sheet Forming, Int. J. for Numerical Methods in Engrg., vol. 63., pp. 473-501, 2005.
  
  
• J.F. Wang, W.D. Carden, R.H. Wagoner, D.K. Matlock and F. Barlat: Creep and Anelasticity in the Springback of Aluminum, Int. J. of Plasticity, Vol. 20, Issue 12, pp. 2209-2232, 2004.
  
  
• J.F. Wang, R.H. Wagoner and D.K. Matlock: Effect of Anticlastic Curvature on Springback of Aluminum Sheets after the Draw-Bend Test, Proc. of NUMIFORM 2004, Materials Processing and Design, eds. S. Ghosh, J. M. Casto and J.K. Lee, Columbus, OH, USA, pp. 820-825, June 2004.(ISBN 0-7354-0189-6)
  
  
• J. Wang and R.H. Wagoner: A New Hexahedral Solid Element for 3D FEM Simulation of Sheet Metal Forming, Proc. of NUMIFORM 2004, Materials Processing and Design, eds. S. Ghosh, J. M. Casto and J.K. Lee, Columbus, OH, USA, pp. 2181-2186, June 2004.(ISBN 0-7354-0189-6)
  
  
• R.H. Wagoner: Sheet Springback, Continuum Scale Simulation of Engineering Materials, Fundamentals - Microstructures - Process Applications, eds. D. Raabe, F. Roters, F. Barlat and L.Q. Chen, Chapt. 42, pp. 777-794, Wiley-VCH, Weinheim, 2004. (ISBN 3-527-30760-5)
  
  
• Y.T. Keum, R.H. Wagoner and J.K. Lee: Friction Model for FEM Simulation of Sheet Metal Forming Operations (N328), Proc. NUMIFORM 2004, pp.989-994, Columbus, OH, June 13-17, 2004.
  
  
• W.D. Carden, L.M. Geng, D.K. Matlock and R.H. Wagoner: Measurement of Springback, Int. J. Mech. Sci., Vol. 44(1), pp. 79- 101, 2002.
  
  
• K.P. Li , W.P. Carden, and R.H. Wagoner: Simulation of Springback, Int. J. Mech. Sci, Vol. 44(1), pp. 103-122, 2002.
  
  
• L. Geng and R.H. Wagoner: Role of Plastic Anisotropy and Its Evolution on Springback, Int. J. Mech. Sci., Vol. 44(1), pp. 123-148, 2002.
  
  
• V. Karthik, R.J. Comstock Jr., D.L. Hershberger and R.H. Wagoner: Variability of Sheet Formability and Formability Testing, Int. J. Mat. Proc. Technol., vol. 121(2-3), pp. 350-362, 2002.
  
  
• L. Geng, Y. Shen and R.H. Wagoner: Anisotropic Hardening Equations Derived from Reverse Bend Testing, Int. J. of Plasticity, Vol. 18 (5-6), pp. 743-767, 2002.
  
  
• R.H. Wagoner: Fundamental Aspects Of Springback In Sheet Metal Forming, Proc. of NUMISHEET 2002, Design Innovation Through Virtual Manufacturing, keynote paper, eds. D.Y. Yang, S.I. Oh, H. Huh and Y. H. Kim, Jeju Island, Korea, vol. 1, pp. 13-24, 2002.
  
  
• Y. Choi, C.S. Han, J.K. Lee, and R.H. Wagoner: Effect of anisotropic axes rotation on springback, Proc. NUMISHEET 2002, Jaeju, Korea, October 2002.
  
  
• C.S. Han, Y. Choi, J.K. Lee and R.H. Wagoner: A FE formulation for elasto-plastic materials with planar anisotropic yield functions and plastic spin, Int'l J. of Solids and Structures, vol. 39, pp. 5123-5141, 2002.
  
  
• C.S. Han, Y. Choi, R.H. Wagoner, and J.K. Lee: Modeling of anisotropic work-hardening with rotation of orthotropic axes, Proc. NUMISHEET 2002, Jaeju, Korea, October 2002.
  
  
• L. Geng and R.H. Wagoner: The Effects of Plastic Anisotropy and Hardening on Sheet Springback, Proceedings of the THERMEC 2000 (CD), eds. T. Chandra, K. Higashi, C. Suryanarayana and C. Tome, 2001. (ISBN 0 08 044026 6)
  
  
• G. Jiang, G.S. Daehn, J.J. Lannutti, Y. Fu and R.H. Wagoner: Effects of Lubrication and Aspect Ratio on the Consolidation of Metal Matrix Composites under Cyclic Pressure, Acta Mater., 49 (8) pp.1471-1477, 2001.
  
  
• G. Jiang, G.S. Daehn and R.H. Wagoner: Void Filling and Cluster Breaking of Metal-Ceramic Composites Under Pressure Cycling, Scripta Mater., 44 287-292, 2001.
  
  
• L. Geng and R.H. Wagoner: Springback Analysis with a Modified Hardening Model, Sheet Metal Forming: Sing Tang 25th Anniversary Volume, SP-1536, Society of Automotive Engineers, Warrendale, PA, pp. 21-32, 2000.(SAE Publication 2000-01-0768).
  
  
• R.H. Wagoner, L. Geng and V. Balakrishnan: Springback Simulation with Non-Isotropic Hardening, Proc. 3rd ESAFORM Conference on Material Forming, ed. H.G. Fritz, Inst. Kunststofftechnologie, University of Stuttgart, pp. VII-3 - VII-6, 2000.
  
  
• S. Sriram and R.H. Wagoner: Adding Bending Stiffness to 3-D Membrane FEM Programs, Int. J. Mech. Sci., Vol. 42, pp. 1753-1782, 2000.
  
  
• R.H. Wagoner, L. Geng and V. Balakrishnan: Role of Hardening Law in Springback, Plastic and Viscoplastic Response of Materials and Metal Forming, eds. A.S. Khan, H. Zhang, Y. Yuan, Neat Press, Baltimore, MD, pp. 609-611, 2000.
  
  
• G. Jiang, Y. Fu, W. Wu, G.S. Daehn and R.H. Wagoner: Enhanced Densification of Metal Matrix Composites Under Cyclic Pressure, Proceedings of PM2TEC, 2000.
  
  
• W. Wu, G. Jiang, R.H. Wagoner and G.S. Daehn: Experimental and Numerical Investigations of Idealized Consolidation Part 1: Static Compaction, Acta Mater., 48 (17) 4323-4330, 2000.
  
  
• W. Wu, G. Jiang, R.H. Wagoner and G.S. Daehn: Experimental and Numerical Investigations of Idealized Consolidation Part 2: Cyclic Compaction, Acta Mater., 48 (17) 4331-4335, 2000.
  
  
• K.P. Li and R.H. Wagoner: Simulation of Deep Drawing with Various Elements, Proceedings of NUMISHEET 99, ed. J.C. Gelin and P. Picart, University of Franche-Compte, Besancon, France, pp. 151-156, 1999.
  
  
• K.P. Li, L.M. Geng, and R.H. Wagoner: Simulation of Springback with the Draw/Bend Test, IPMM 99, Vol. 1, eds. J.A. Meech, M.M. Veiga, M.H. Smith, S.R. LeClair, IEEE, Vancouver, BC, Canada, pp. 91-104, 1999.(ISBN 0-7803-5489-3)
  
  
• K. Li, L. Geng, and R.H. Wagoner: Simulation of Springback: Choice of Element, Advanced Technology of Plasticity 1999, Vol. III, ed. M. Geiger, Springer-Verlag, Berlin, pp. 2091-2098, 1999.
  
  
• M.C. Stasik and R.H. Wagoner: Forming of Tailor-Welded Aluminum Blanks, Int. J. Form. Processes, vol. 1 (1), pp. 9-33, 1998.
  
  
• S. Sriram and R.H. Wagoner: Failure Prediction with the Limiting Dome Height Test, Int. J. Form. Processes, vol. 1 (1), pp. 97-117, 1998.
  
  
• K. Li and R.H. Wagoner: Simulation of Springback, Simulation of Materials Processing, eds. J. Huetink and F.P.T. Baaijens, A.A. Balkema, Rotterdam, pp. 21-31, 1998.
  
  
• V. Talyan, R.H. Wagoner, and J.K. Lee: Formability of Stainless Steel, Metall. Mater. Trans. A, vol. 29A, pp. 2161-2172, 1998.
  
  
• V. Talyan, R.H. Wagoner, and J.K. Lee: Formability of Stainless Steel, Constitutive and Damage Modeling of Inelastic Deformation and Phase Transformation, Ed. A.S. Khan, Neat Press, pp. 425-428, 1998.
  
  
• D. Zhou and R.H. Wagoner: An Algorithm for Improved Convergence in Forming Analysis, Int. J. Mech. Sci., vol. 39, No. 12, pp. 1363-1384, 1997.
  
  
• C. Wong, M.L. Wenner and R.H. Wagoner: Corner Design in Deep-Drawn Rectangular Parts, Sheet Metal Stamping, Warrendale, PA, pp. 39-55, 1997.(SAE Publ. No. SP-1221)
  
  
• R.H. Wagoner, W.D. Carden, W.P. Carden, and D.K. Matlock: Springback after Drawing and Bending of Metal Sheets, Proc. IPMM '97 - Intelligent Processing and Manufacturing of Materials, eds. T.Chandra, S.R. Leclair, J.A. Meech, B. Verma, M. Smith and B. Balachandran, University of Wollongong, vol. 1 (Intelligent Systems Applications), pp. 1-10 [KEYNOTE], 1997.
  
  
• R.H. Wagoner and S. Sriram: Lessons Learned from Sheet Forming Benchmark Tests, THERMEC '97 - Thermomechanical Processing of Steel and Other Materials, eds. T. Chandra and T. Sakai, The Minerals, Metals, and Materials Society, Warrendale, PA, pp. 249-255, 1997.
  
  
• W. Wang, R.H. Wagoner, and X.J. Wang: Measurement of Friction Under Sheet Forming Conditions, Metall. Mat. Trans. A, vol. 27A, pp. 3971-3981, 1996.
  
  
• F.I. Saunders and R.H. Wagoner: Forming of Tailor-Welded Aluminum Blanks, Metall. Mat. Trans. A, vol. 27A, pp. 2605-2615, 1996.
  
  
• S. Sadagopan and R.H. Wagoner: Simulating the LDH Test, NUMISHEET 96, eds. J.K. Lee, G.L. Kinzel and R.H. Wagoner, The Ohio State University, pp. 128-135, 1996.
  
  
• S. Sriram, R.H. Wagoner, and D. Gearing: Affordable Testing for Sheet Forming Applications, Advanced Technology of Plasticity 1996 - Vol. II, ed. T. Altan, The Ohio State University, pp. 843-856, 1996.
  
  
• N. He and R.H. Wagoner: Springback Simulation in Sheet Metal Forming, NUMISHEET 96, eds. J.K. Lee, G.L. Kinzel, R.H. Wagoner, The Ohio State University, pp. 308-315, 1996.
  
  
• J.K. Lee, G.L. Kinzel and R.H. Wagoner, editors: NUMISHEET '96,The Ohio State University, 847 pages, 1996.
  
  
• Y. Kong, Y. Sun, X. Wang and R.H. Wagoner: Development of a New Friction Test Device in Sheet Forming, Advanced Technology of Plasticity 1996 - Vol. II, ed. T. Altan, The Ohio State University, pp. 835-838, 1996.
  
  
• K. Narasimhan, M.P. Miles, and R.H. Wagoner: A Better Sheet Formability Test, J. Mat. Proc. Technol., vol. 50, pp. 385-394, 1995.
  
  
• Y.T. Keum, Y.S. Suh, K. Chung, and R.H. Wagoner: 3-D FEM Analysis of Forming Operations for Planar Anisotropic Sheet Panels, Computational Mechanics '95, eds. S.N. Atluri, G. Yagawa, T.A. Cruise, Springer, Berlin, pp. 1408-1413, 1995.
  
  
• F.I. Saunders and R.H. Wagoner: The Use of Tailor-Welded Blanks in Automotive Applications, Simulation of Materials Processing: Theory, Methods, and applications - NUMIFORM 95, eds. S.F. Shen and P. Dawson, Balkema, Rotterdam, pp. 157-164, 1995.
  
  
• R.H. Wagoner, D. Zhou, and S. Sriram: The Element Bending Group Method, Computational Mechanics '95, eds. S.N. Atluri, G. Yagawa, T.A. Cruise, Springer, Berlin, pp. 1390-1395, 1995.
  
  
• D. Zhou and R.H. Wagoner: Development and Application of Sheet Forming Simulation, J. Mat. Proc. Technol., vol. 50, pp. 1-16, 1995.
  
  
• R.H. Wagoner, W. Wang, and S. Sriram: Development of OSU Formability Test and OSU Friction Test, J. Mat. Proc. Technol., vol. 45, pp. 13-18, 1994.
  
  
• S. Sriram, T. Brovold, and R.H. Wagoner: An Affordable Sheet Formability Test System, Metal Forming, vol. 28, pp. 63-70, 1994.
  
  
• R.M. Harycki, K.E. Gasper, R.J. Smola, F.I. Saunders, J.M. Garrett, and R.H. Wagoner: A New Method for Ranking Sheet Metal Lubricants, MetalForming, vol. 28, pp. 39-47, 1994.
  
  
• M.P. Miles, J.L. Siles, R.H. Wagoner, and K. Narasimhan: A Better Sheet Formability Test, Metall. Trans. A, vol. 24A, pp. 1143 - 1151, 1993.
  
  
• Y.S. Suh and R.H. Wagoner: Optimized Design of Tooling of the New Formability Test Using Finite Element Method, Computer Applications in Shaping and Forming Materials, ed. M.Y. Demeri, The Minerals, Metals, and Materials Society, Warrendale, PA, pp. 221-230, 1993.
  
  
• W. Wang and R.H. Wagoner: A Realistic Friction Test for Sheet Forming Operations, Advanced Technology of Plasticity - 1993, eds. Z.R. Wang and H. Yuxin, Int. Academic Publ., Beijing, pp. 1495-1500, 1993.
  
  
• F.I. Saunders, M.P. Miles, J.L. Siles and R.H. Wagoner: A Better Sheet Formability Test, Metal Forming, vol. 27, pp. 31-34, 1993.
  
  

Glenn S. Daehn

• G. Jiang, G.S. Daehn, J.J. Lannutti, Y. Fu and R.H. Wagoner: Effects of Lubrication and Aspect Ratio on the Consolidation of Metal Matrix Composites under Cyclic Pressure, Acta Mater., 49 (8) pp.1471-1477, 2001.
  
  
• G. Jiang, G.S. Daehn and R.H. Wagoner: Void Filling and Cluster Breaking of Metal-Ceramic Composites Under Pressure Cycling, Scripta Mater., 44 287-292, 2001.
  
  
• G.S. Daehn, V.J. Vohnout and S. Datta: Hyperplastic Forming: Process Potential and Factors Affecting Formability, Superplasticity and Superplastic Forming, P.B. Berbon, M.Z. Berbon, T. Sakuma and T.G. Langdon, editors, Volume 601, pp. 247-253, 2000.
  
  
• G. Jiang, Y. Fu, W. Wu, G.S. Daehn and R.H. Wagoner: Enhanced Densification of Metal Matrix Composites Under Cyclic Pressure, Proceedings of PM2TEC, 2000.
  
  
• W. Wu, G. Jiang, R.H. Wagoner and G.S. Daehn: Experimental and Numerical Investigations of Idealized Consolidation Part 1: Static Compaction, Acta Mater., 48 (17) 4323-4330, 2000.
  
  
• W. Wu, G. Jiang, R.H. Wagoner and G.S. Daehn: Experimental and Numerical Investigations of Idealized Consolidation Part 2: Cyclic Compaction, Acta Mater., 48 (17) 4331-4335, 2000.
  
  
• G.S. Daehn, V.J. Vohnout and A. Tamhane: Electromagnetic actuator, method of use and article made there from, U. S. Patent 5,860,306, Issued January 19, 1999.
  
  
• V.J. Vohnout, G.S. Daehn and R. Shivpuri: A Hybrid Quasi-Static-Dynamic Process for Increased Limiting Strains in the Forming of Large Sheet Aluminum Parts, Advanced Technology of Plasticity, Proceedings of the 6th ICTP Conf., ed. M. Geiger, pp. 1359-64, 1999.
  
  
• L. Ceschini, G.S. Daehn, G.L. Garagnani and C. Martini: Friction and wear behaviour of C4 Al2O3/Al composites under dry sliding conditions, Wear 216, pp 229-38, 1998.
  
  
• G. Fenton and G.S. Daehn: Modeling Electromagnetic Forming of Sheet Metal, J. Mater. Proc. Tech. 75 pp.6-16, 1998.
  
  
• A.A. Tamnane, V.J. Vohnout, M. Padmanabhan, G. Fenton, V.S. Balanethiram, M. Altynova and G.S. Daehn: Opportunities in the High Velocity Forming of Sheet Metal, Metal Forming, pp. 42-49, January 1997.
  
  
• V.J. Vohnout, M. Altynova, V.S. Balanethiram, M. Padmanabhan, G. Fenton, A.A. Tamhane and G.S. Daehn: High Velocity Sheet Metal Forming: Recent Advances and Applications, FabTech '97 Conf. Proc. pp. 1413-29, 1997.
  
  
• Impulsive Forming of Sheet Aluminum: Cost Effective Technology for Complex Component Manufacturing, Proceedings of Alumitech, Atlanta, GA, May 1997.
  
  
• M. Padmanabhan: Wrinkling and Springback in Electromagnetic Sheet Metal Forming and Electromagnetic Ring Compression, M.S. Degree, The Ohio State University, Advised by G.S. Daehn, 1997.
  
  

June K. Lee

• Y.T. Keum, R.H. Wagoner and J.K. Lee: Friction Model for FEM Simulation of Sheet Metal Forming Operations (N328), Proc. NUMIFORM 2004, pp.989-994, Columbus, OH, June 13-17, 2004.
  
  
• K.M. Zhao and J.K. Lee: Inverse Estimation of Material Properties for Sheet Metals, Communication in Numerical Methods in Engineering, 20-2, PP. 105-118, 2004.
  
  
• C.S. Han, Y. Choi, R.H. Wagoner, and J.K. Lee: Modeling of anisotropic work-hardening with rotation of orthotropic axes, Proc. NUMISHEET 2002, Jaeju, Korea, October 2002.
  
  
• Y. Choi, C.S. Han, J.K. Lee, and R.H. Wagoner: Effect of anisotropic axes rotation on springback, Proc. NUMISHEET 2002, Jaeju, Korea, October 2002.
  
  
• K.M. Zhao and J.K. Lee: Finite Element Analysis of the Three-Point Bending of Sheet Metals, Journal of Materials Processing Technology, 122, pp. 6-11, 2002.
  
  
• B.K. Chun, J.T. Jinn, and J.K. Lee: Modeling the Bauschinger effect for sheet metals - Part I: Theory, International journal of Plasticity, vol. 18/5-6, pp. 571-595, April 2002.
  
  
• B.K. Chun, H.Y. Kim, and J.K. Lee: Modeling the Bauschinger effect for sheet metals- Part II: Applications, International journal of Plasticity, vol. 18/5-6, pp. 597-616, April 2002.
  
  
• H.J. Kim, J.S. Kim, M.E. Walter, and J.K. Lee: The Thermo-Mechanical Stress-Strain Response of Intumescent Mat Materials through Experiments and Strain Decomposition, Journal of Strain Analysis, vol. 37, No. 3, 2002.
  
  
• J.S. Kim, M.E. Walter and J.K. Lee: Modeling Mechanical Response of Intumescent Mat Material at Room Temperature, International Journal of Mechanical Sciences, 44, pp. 2285-2315, 2002.
  
  
• C.S. Han, Y.W. Choi, J.K. Lee and R.H. Wagoner: A FE formulation for elasto-plastic materials with planar anisotropic yield functions and plastic spin, International Journal of Solids and Structures, 39, p. 5123-5141, 2002.
  
  
• J.H. Choi, Y.W Choi, J. Na and J.K. Lee: Total finite element analysis system for the design of an automotive catalytic converter, SAE 2002 World Congress and Exhibition, Paper No. 02FL-51, 2002.
  
  
• J.K. Lee, Y.W. Choi, S.K. Lee, B.K. Chun and H.Y. Kim: Three-dimensional springback prediction for draw bead test simulation by using anisotropic nonlinear kinematic hardening model, Proc. NUMISHEET 2002, Jaeju, Korea, October 2002.
  
  
• K.M. Zhao and J.K. Lee: Material Properties of Aluminum Alloy for Accurate Draw-Bend Simulation, Transactions of the ASME, Journal of Engineering Materials and Technology, vol. 123, pp. 287-292, July 2001.
  
  
• K.M. Zhao and J.K. Lee: Finite Element Analysis of Tailor Welded Blanks, Finite Element in Analysis and Design, 37 (2001), pp. 117-130.
  
  
• K.M. Zhao and J.K. Lee: Generation of Cyclic Stress-Strain Curves for Sheet Metals, Transactions of the ASME, Journal of Engineering Materials and Technology, vol. 123, pp. 391-397, October 2001,
  
  
• B.K. Chun, J.T. Jinn and J.K. Lee: A constitutive model associated with permanent softening under multiple bend-unbend cycles in sheet metal forming and springback analysis, Proc. First MIT Conference on Computational Fluid and Solid Mechanics, Ed. K.J. Bathe, Vol.1, pp.120-124, Cambridge, MA, USA, June 12-15, 2001.(ISBN 008 043944 6)
  
  
• J.K. Lee, B.K. Chun and H.Y. Kim: Numerical Investigation of Tailor Welded Blank Forming and Springback, Proc. NUMIFORM 2001-Simulation of Materials Processing: Theory, Methods and Applications, Ed. K. Mori, pp. 729-734, Toyohashi, Japan, June 18-21, 2001.(ISBN 90 2651 822 6)
  
  
• J.K. Lee, B.K. Chun, J.T. Jinn and H.Y. Kim: Modeling the Bauschinger effect for sheet metals, Symposium on Sheet Metal Forming USNCCM VI, Dearborn, Michigan, August 1-3, 2001.
  
  
• K.M. Zhao, B.K. Chun and J.K. Lee: Numerical Modeling Technique for Tailor Welded Blanks, Sheet Metal Stamping (SP-1540), Proc. SAE 2000 World Congress, March 6-9, 2000, Detroit, Michigan, pp. 1-7.(Paper No. 2000-01-0410)
  
  
• K.M. Zhao and J.K. Lee: Springback Prediction Using Combined Hardening Model, IBEC'2000, Proc. International Body Engineering Conference & Exposition, pp.1-9, Detroit, MI, October 3-5, 2000.
  
  
• K.M. Zhao and J.K. Lee: Estimation of Material Properties from Cyclic Bend Test, IBEC'2000, Proc. International Body Engineering Conference & Exposition, pp. 10-18, October 3-5, 2000, Detroit, MI.(Paper No. 2000-01-2660)
  
  
• K.M. Zhao, and J.K. Lee: Generation of cyclic stress-strain curves for sheet metals, ASME, MED-Vol. 11, Manufacturing in Engineering Division - 2000, pp. 667-674, Proceedings Of The ASME International Mechanical Engineering Congress and Exposition, Orlando, Florida, November 2000.
  
  
• J. Fuehne, W. Taylor, J. Kim, and J.K. Lee: Characterization of Catalytic Converter Mat Material for Predictive Analysis, SAE 2000 World Congress, Detroit, Michigan, March 6-9, 2000.(Paper No. 2000-01-0218)
  
  
• W. Taylor, J. Fuehne, R. Lyon, J.K. Lee, and J. Kim: FEA Simulation and Experimental Validation of Catalytic Converter Structural Integrity, SAE 2000 World Congress,Detroit, Michigan, March 6-9, 2000,.(Paper No. 2000-01-0219)
  
  
• A.H. Clauer, R.A. Brockman, W.R. Braisted, S.A. Noll, J.K. Lee, and A. Gilat: Modeling Residual Stresses from Laser Shock Peening, Proc. 5th Int. Conf. High Cycle Fatigue, 10 pages on a CD, Tempe, Arizona, March 2000.
  
  
• B.K. Chun, H.Y. Kim, J.K. Lee and K.Y. Choi: Effects of material modeling on springback prediction in draw/bend test using Pam-Stamp, Proc. AMERIPAM 2000,Detroit, Michigan, Oct. 2000.
  
  
• B.K. Chun, H.Y. Kim, J.K. Lee and K.Y. Choi: Effects of Hardening model on springback prediction in draw/bend test, Proc. HANPAM 2000, Seoul, Korea, Nov. 2000.
  
  
• J.K. Lee: Status and Research Issues in Sheet Metal Forming for Light Weight Automotive Components, 4th Steel Symposium: Manufacture and Application of Automotive Steels, Korea Institute of Metals, Invited Keynote Lecture Paper, pp. 235-244, Seoul, Korea, August 27-28 1999.
  
  
• K.M. Zhao and J.K. Lee: On Simulation of Bending/Reverse Bending of Sheet Metals, Manufacturing Science And Engineering, ASME MED -Vol. 10, pp. 929-933, Ed. J.W. Sutherland, Proceedings of The ASME International Mechanical Engineering Congress and Exposition, Nashville, Tennessee, November 14-19, 1999.
  
  
• S. Esche, G.L. Kinzel, and J.K. Lee: An Axisymmetric Membrane Element with Bending Stiffness for Static Implicit Sheet Metal Forming Simulations, Trans. ASME Journal of Applied Mechanics, Volume 66, No. 1, pp. 153-164, 1999.
  
  
• V. Talyan, R.H. Wagoner, and J.K. Lee: Formability of Stainless Steel, Metall. Mater. Trans. A, vol. 29A, pp. 2161-2172, 1998.
  
  
• V. Talyan, R.H. Wagoner, and J.K. Lee: Formability of Stainless Steel, Constitutive and Damage Modeling of Inelastic Deformation and Phase Transformation, Ed. A.S. Khan, Neat Press, pp. 425-428, 1998.
  
  
• H.S. Park, Y.T. Keum and J.K. Lee: Numerical Simulation of Ceramic Sintering Process, J. Materials Processing, Transactions of the KSME., Vol 23, pp. 25-43, 1997.
  
  
• S. Ghosh, Z. Nowak and J.K. Lee: Quantitative characterization and modeling of composite microstructures by Voronoi cells, Acta Materialia, Vol. 45, No. 6, pp. 2215-2234, 1997.
  
  

Mark E. Walter

• (erratum)H.J. Kim and M.E. Walter: Characterization of the degraded microstructures of a platinum aluminide coating, Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 393 (1-2): 399-400 Feb 25 2005.
  
  
• H. Kim: Investigation of Critical Issues in Thermal Barrier Coating Durability, PhD Degree, The Ohio State University, Advised by M.E. Walters, 2005.
  
  
• S. Nekkanty and M.E. Walter: Indentation damage to boron carbide-DLC coatings with different compositions, Surface & Coatings Technology 183 (1): 1-9, May 1 2004.
  
  
• H.J. Kim and M.E. Walter: Characterization of the degraded microstructures of a platinum aluminide coating, Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 360 (1-2): 7-17, Nov 15 2003
  
  
• J.M. Reed and M.E. Walter: Observations of serration characteristics and acoustic emission during serrated flow of an Al-Mg alloy, Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 359 (1-2): 1-10, Oct 25 2003.
  
  
• H.J. Kim, J.S. Kim, M.E. Walter, and J.K. Lee: The Thermo-Mechanical Stress-Strain Response of Intumescent Mat Materials through Experiments and Strain Decomposition, Journal of Strain Analysis, vol. 37, No. 3, 2002.
  
  
• J.S. Kim, M.E. Walter and J.K. Lee: Modeling Mechanical Response of Intumescent Mat Material at Room Temperature, International Journal of Mechanical Sciences, 44, pp. 2285-2315, 2002.
  
  
• S. Nekkanty: Characterization of Indentation Damage to Boron Carbide/DLC Coatings, M.S. Degree, The Ohio State University, Advised by M.E. Walter, 2002.
  
  

Gary L. Kinzel

• J.T. Gau and G.L. Kinzel: An Experimental Investigation of the Influence of the Baushinger Effect on Springback Predictions, Journal of Materials Processing Technology, Vol. 108, pp.369-375, 2001.
  
  
• J.T. Gau and G.L. Kinzel: A new model for springback prediction in which the Bauschinger effect is considered, International Journal of Mechanical Sciences, Vol. 43, No. 8, pp.1813-1832, 2001.
  
  
• S. Esche, M. Ahmetoglu, G. Kinzel, and T. Altan: Numerical and Experimental Investigation of Redrawing of Sheet Metal, Journal of Materials Processing Technology, 98, pp. 17-24, 2000.
  
  
• S. Esche, G.L. Kinzel, and J.K. Lee: An Axisymmetric Membrane Element with Bending Stiffness for Static Implicit Sheet Metal Forming Simulations, Trans. ASME Journal of Applied Mechanics, Volume 66, No. 1, pp. 153-164, 1999.
  
  
• J.T. Gau: A Study of the Influence of the Bauschinger Effect on Springback in Two-Dimensional Sheet Metal Forming, Ph.D. Degree, The Ohio State University, Advised by G. Kinzel, Summer, 1999.
  
  
• R.S. Sattanathan: Design of User Interfaces for Engineering Applications, M.S. Degree, The Ohio State University, Advised by G. Kinzel, 1997.
  
  
• S.K. Essche: Developments for Two-Dimensional Sheet Metal Forming Analysis, PhD, The Ohio State University, Advised by G. Kinzel, Summer, 1997.
  
  

Somnath Ghosh

• S. Ghosh, Z. Nowak and K. Lee: Quantitative characterization and modeling of composite microstructures by Voronoi cells, Acta Materialia, Vol. 45, No. 6, pp. 2215-2234, 1997.
  
  
• S. Ghosh and S. Raju: Localized metal forming simulation by R-S adapted ALE finite element method, Journal of Strain Analysis, Vol. 32, No. 4, pp. 237-252, 1997.
  
  

Stephen E. Bechtel

• W.F. Pon: A Model for Electromagnetic Ring Expansion Experiment and its Application to Materials Characterization, PhD, The Ohio State University, Advised by S. Bechtel, 1997.
  
  
• The Manufacture of Polymer Fibers, The Ohio State University Center for Materials Research seminar series on polymer research, February 1996.
  
  

Charles E. Albright

• S. Ramasamy, and C.E. Albright: CO2 and Laser Welding of 5754-O Aluminum Alloy for Automotive Applications, Sci. and Tech. of Welding and Joining, Vol. 6, No. 3, March, 2001.
  
  
• S. Ramasamy, and C.E. Albright: CO2 and Laser Welding of 6111-T4 Aluminum Alloy for Automotive Applications, J. Laser Appl., Vol. 12, No. 3, June, 2000
  
  
• S. Ramasamy: Laser Welding of Aluminum Alloys, PhD, The Ohio State University, Advised by C. Albright, 1997.